How to Make an Airsoft Gun Out of a Cap Gun

How to Make an Airsoft Gun Out of a Cap Gun

Download Article

Download Commodity

This is how to brand a absurd airsoft gun out of a Nerf gun. Note: the bigger the gun the amend; a pump Nerf gun gives you more fps (feet per sec).

Steps

1. 1

   Go a Nerf gun; any volition do.

2. 2

   Get a Nerf Dart (the ammo for Nerf gun) and pull the end off of information technology. You volition have a foam tube.

   Advertizing

3. iii

   Get a Bic pen and use pliers to take out the dorsum and front so yous take a tube.

4. 4

   Stick the Bic pen tube into the foam tube; well-nigh half of the pen should be covered by the dart.

5. 5

   Place the sprint finish into the barrel, push downwardly on the dart as far as you lot can, then push the pen tube into the barrel.

6. 6

   Cock and shoot zip a few times to ensure that it doesn't fall out.

7. 7

   Cock and shoot at your paw, if air pressure is present, good job!

   Advertizement

Add New Question

• Question

  Does this work with any Nerf gun?

  

  TaterBoi

  Customs Answer

  Yes, this method will work for any front-loading Nerf blasters.

• Question

  Will a copper BB piece of work?

  

  Information technology may, but information technology is a piddling smaller than the Airsoft BB. If it doesn't work, you could endeavour using a smaller pen tube.

• Question

  How can I exercise this with a Sharpfire?

  

  You cannot, unfortunately. The Sharpfire is impossible to change in this way.

• Question

  How practise I make an Airsoft gun out of a Nerf rifle that shoots balls?

  

  Block off all forms of air escape except the butt, and use a straw or pen tube in that location. Make certain air goes through the tube.

• Question

  How do I make this one with the Retaliator?

  

  Viktor Simbulan

  Community Respond

  Information technology might exist hard to make it with a Retaliator since it is prune-fed. Try a Jolt, or any other front-loaders.

• Question

  Can I employ the Nerf RaptorStrike to exercise this? If so, how?

  

  No, it is a clip loader and so it probably wouldn't work. Try a front-loader, like a Jolt.

• Question

  Tin can I use a straw instead of a pen tube to make an Airsoft gun out of a Nerf gun?

  

  Yes you can they will both piece of work the same, just don't twist or bite the straw.

• Question

  How practise I take the top of a dart off?

  

  This is piece of cake; only rip information technology off or cut it with scissors. It's that simple.

• Question

  What should I use for armament?

  

  Airsoft BBs are used.

• Question

  Do I accept to apply a pen to do this?

  

  No. Any tube that fits will work. Just follow the instructions in a higher place to get in.

Show more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advert

Video

• The pen tube volition stay in better if the record on the end is crumpled a little.

• You tin can paint your gun black similar a normal Airsoft gun if you want, but to stay legal get out the orange tip.

• Brand sure you don't hit anyone unless you are in an Airsoft war.

Thank you for submitting a tip for review!

Advert

Things You'll Need

• Nerf gun (whatever)
• Pen medium
• Tape (any)
• Ammo (anything that fits well in the pen tube)

About This Article

Thanks to all authors for creating a page that has been read 97,985 times.

Did this article help y'all?

How to Make an Airsoft Gun Out of a Cap Gun

Posted by: silersaidgety.blogspot.com

Share this post